Quick view Details sku: DC-1000 DC Power Jack 2.1mm - Innie MSRP: Now: $0.50 Add to Cart Compare Quick view Details sku: DC-1004 DC Power Jack 2.1mm - Low Profile MSRP: Now: $0.60 Add to Cart Compare Quick view Details sku: DC-1002 DC Power Jack 2.1mm - Outie MSRP: Now: $0.65 Add to Cart Compare Quick view Details Lumberg | sku: DC-1005 DC Power Jack 2.1mm - Lumberg 1614 09 MSRP: Now: $1.85 Add to Cart Compare Quick view Details sku: DC-1001 DC Power Jack 2.1mm - PCB Mount MSRP: Now: $0.35 Add to Cart Compare Quick view Details sku: BAT-1009 9v Battery Clip - Vinyl MSRP: Now: $0.35 Add to Cart Compare Quick view Details sku: BAT-1020 9v Battery Clip - Plastic MSRP: Now: $0.35 Add to Cart Compare Quick view Details sku: KIT-1000 "The Essentials" Hardware Kit MSRP: Now: $7.00 Add to Cart Compare Quick view Details Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 MSRP: Now: $1.35 Add to Cart Compare SALE Quick view Details sku: BAT-1022 9v Battery Clip - Plastic - Short Lead MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Details Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Quick view sku: DC-1000 DC Power Jack 2.1mm - Innie Stardard power jack, internal nut. Low profile on the outside so pedals can be wedged closer together. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 15/32" (12mm) diameter hole. Three solder lug. Switched to disconnect... MSRP: Now: $0.50 Add to Cart Compare Quick view sku: DC-1004 DC Power Jack 2.1mm - Low Profile Low profile power jack. If you want a real Lumberg jack, find those here! Takes "standard" 5.5mm plug with 2.1mm center pin. It is a tighter squeeze on the power cable than the bigger DC jacks. It'll fit, and you won't need to worry about... MSRP: Now: $0.60 Add to Cart Compare Quick view sku: DC-1002 DC Power Jack 2.1mm - Outie Stardard power jack, the external "outie" version. The body of this jack sits outside of the pedal to save space on the inside. Comes with flat washer and star washer. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 1/2" (12... MSRP: Now: $0.65 Add to Cart Compare Quick view Lumberg | sku: DC-1005 DC Power Jack 2.1mm - Lumberg 1614 09 *DISCONTINUED. Once they're gone they will not be restocked. 1614 23 is the updated Lumberg part* The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. Superior connection and fit... MSRP: Now: $1.85 Add to Cart Compare Quick view sku: DC-1001 DC Power Jack 2.1mm - PCB Mount Standard PCB mount power jack. Takes "standard" 5.5mm plug with 2.1mm center pin. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1009 9v Battery Clip - Vinyl Battery snap for 9v battery. Vinyl insulator.6" (150mm) pre-tinned leads. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1020 9v Battery Clip - Plastic Battery snap for 9v battery. 6" (150mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Now: $0.35 Add to Cart Compare Quick view sku: KIT-1000 "The Essentials" Hardware Kit The Essentials! All the standard hardware you'll need for any build. This pack includes:1x 3PDT Pro footswitch with solder lugs1x TRS enclosed 1/4" jack1x TS enclosed 1/4" jack1x DC power jack - "outie"1x 5mm LED (leave a comment in checkout if... MSRP: Now: $7.00 Add to Cart Compare Quick view Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. These are Lumberg's updated version of the discontinued 1614 09. The insertion/removal force is a bit tighter on the new model... MSRP: Now: $1.35 Add to Cart Compare SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Compare Selected × OK
Quick view Details sku: DC-1004 DC Power Jack 2.1mm - Low Profile MSRP: Now: $0.60 Add to Cart Compare Quick view Details sku: DC-1002 DC Power Jack 2.1mm - Outie MSRP: Now: $0.65 Add to Cart Compare Quick view Details Lumberg | sku: DC-1005 DC Power Jack 2.1mm - Lumberg 1614 09 MSRP: Now: $1.85 Add to Cart Compare Quick view Details sku: DC-1001 DC Power Jack 2.1mm - PCB Mount MSRP: Now: $0.35 Add to Cart Compare Quick view Details sku: BAT-1009 9v Battery Clip - Vinyl MSRP: Now: $0.35 Add to Cart Compare Quick view Details sku: BAT-1020 9v Battery Clip - Plastic MSRP: Now: $0.35 Add to Cart Compare Quick view Details sku: KIT-1000 "The Essentials" Hardware Kit MSRP: Now: $7.00 Add to Cart Compare Quick view Details Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 MSRP: Now: $1.35 Add to Cart Compare SALE Quick view Details sku: BAT-1022 9v Battery Clip - Plastic - Short Lead MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Details Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Quick view sku: DC-1000 DC Power Jack 2.1mm - Innie Stardard power jack, internal nut. Low profile on the outside so pedals can be wedged closer together. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 15/32" (12mm) diameter hole. Three solder lug. Switched to disconnect... MSRP: Now: $0.50 Add to Cart Compare Quick view sku: DC-1004 DC Power Jack 2.1mm - Low Profile Low profile power jack. If you want a real Lumberg jack, find those here! Takes "standard" 5.5mm plug with 2.1mm center pin. It is a tighter squeeze on the power cable than the bigger DC jacks. It'll fit, and you won't need to worry about... MSRP: Now: $0.60 Add to Cart Compare Quick view sku: DC-1002 DC Power Jack 2.1mm - Outie Stardard power jack, the external "outie" version. The body of this jack sits outside of the pedal to save space on the inside. Comes with flat washer and star washer. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 1/2" (12... MSRP: Now: $0.65 Add to Cart Compare Quick view Lumberg | sku: DC-1005 DC Power Jack 2.1mm - Lumberg 1614 09 *DISCONTINUED. Once they're gone they will not be restocked. 1614 23 is the updated Lumberg part* The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. Superior connection and fit... MSRP: Now: $1.85 Add to Cart Compare Quick view sku: DC-1001 DC Power Jack 2.1mm - PCB Mount Standard PCB mount power jack. Takes "standard" 5.5mm plug with 2.1mm center pin. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1009 9v Battery Clip - Vinyl Battery snap for 9v battery. Vinyl insulator.6" (150mm) pre-tinned leads. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1020 9v Battery Clip - Plastic Battery snap for 9v battery. 6" (150mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Now: $0.35 Add to Cart Compare Quick view sku: KIT-1000 "The Essentials" Hardware Kit The Essentials! All the standard hardware you'll need for any build. This pack includes:1x 3PDT Pro footswitch with solder lugs1x TRS enclosed 1/4" jack1x TS enclosed 1/4" jack1x DC power jack - "outie"1x 5mm LED (leave a comment in checkout if... MSRP: Now: $7.00 Add to Cart Compare Quick view Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. These are Lumberg's updated version of the discontinued 1614 09. The insertion/removal force is a bit tighter on the new model... MSRP: Now: $1.35 Add to Cart Compare SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Compare Selected × OK
Quick view Details sku: DC-1002 DC Power Jack 2.1mm - Outie MSRP: Now: $0.65 Add to Cart Compare Quick view Details Lumberg | sku: DC-1005 DC Power Jack 2.1mm - Lumberg 1614 09 MSRP: Now: $1.85 Add to Cart Compare Quick view Details sku: DC-1001 DC Power Jack 2.1mm - PCB Mount MSRP: Now: $0.35 Add to Cart Compare Quick view Details sku: BAT-1009 9v Battery Clip - Vinyl MSRP: Now: $0.35 Add to Cart Compare Quick view Details sku: BAT-1020 9v Battery Clip - Plastic MSRP: Now: $0.35 Add to Cart Compare Quick view Details sku: KIT-1000 "The Essentials" Hardware Kit MSRP: Now: $7.00 Add to Cart Compare Quick view Details Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 MSRP: Now: $1.35 Add to Cart Compare SALE Quick view Details sku: BAT-1022 9v Battery Clip - Plastic - Short Lead MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Details Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Quick view sku: DC-1000 DC Power Jack 2.1mm - Innie Stardard power jack, internal nut. Low profile on the outside so pedals can be wedged closer together. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 15/32" (12mm) diameter hole. Three solder lug. Switched to disconnect... MSRP: Now: $0.50 Add to Cart Compare Quick view sku: DC-1004 DC Power Jack 2.1mm - Low Profile Low profile power jack. If you want a real Lumberg jack, find those here! Takes "standard" 5.5mm plug with 2.1mm center pin. It is a tighter squeeze on the power cable than the bigger DC jacks. It'll fit, and you won't need to worry about... MSRP: Now: $0.60 Add to Cart Compare Quick view sku: DC-1002 DC Power Jack 2.1mm - Outie Stardard power jack, the external "outie" version. The body of this jack sits outside of the pedal to save space on the inside. Comes with flat washer and star washer. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 1/2" (12... MSRP: Now: $0.65 Add to Cart Compare Quick view Lumberg | sku: DC-1005 DC Power Jack 2.1mm - Lumberg 1614 09 *DISCONTINUED. Once they're gone they will not be restocked. 1614 23 is the updated Lumberg part* The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. Superior connection and fit... MSRP: Now: $1.85 Add to Cart Compare Quick view sku: DC-1001 DC Power Jack 2.1mm - PCB Mount Standard PCB mount power jack. Takes "standard" 5.5mm plug with 2.1mm center pin. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1009 9v Battery Clip - Vinyl Battery snap for 9v battery. Vinyl insulator.6" (150mm) pre-tinned leads. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1020 9v Battery Clip - Plastic Battery snap for 9v battery. 6" (150mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Now: $0.35 Add to Cart Compare Quick view sku: KIT-1000 "The Essentials" Hardware Kit The Essentials! All the standard hardware you'll need for any build. This pack includes:1x 3PDT Pro footswitch with solder lugs1x TRS enclosed 1/4" jack1x TS enclosed 1/4" jack1x DC power jack - "outie"1x 5mm LED (leave a comment in checkout if... MSRP: Now: $7.00 Add to Cart Compare Quick view Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. These are Lumberg's updated version of the discontinued 1614 09. The insertion/removal force is a bit tighter on the new model... MSRP: Now: $1.35 Add to Cart Compare SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Compare Selected × OK
Quick view Details Lumberg | sku: DC-1005 DC Power Jack 2.1mm - Lumberg 1614 09 MSRP: Now: $1.85 Add to Cart Compare Quick view Details sku: DC-1001 DC Power Jack 2.1mm - PCB Mount MSRP: Now: $0.35 Add to Cart Compare Quick view Details sku: BAT-1009 9v Battery Clip - Vinyl MSRP: Now: $0.35 Add to Cart Compare Quick view Details sku: BAT-1020 9v Battery Clip - Plastic MSRP: Now: $0.35 Add to Cart Compare Quick view Details sku: KIT-1000 "The Essentials" Hardware Kit MSRP: Now: $7.00 Add to Cart Compare Quick view Details Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 MSRP: Now: $1.35 Add to Cart Compare SALE Quick view Details sku: BAT-1022 9v Battery Clip - Plastic - Short Lead MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Details Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Quick view sku: DC-1000 DC Power Jack 2.1mm - Innie Stardard power jack, internal nut. Low profile on the outside so pedals can be wedged closer together. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 15/32" (12mm) diameter hole. Three solder lug. Switched to disconnect... MSRP: Now: $0.50 Add to Cart Compare Quick view sku: DC-1004 DC Power Jack 2.1mm - Low Profile Low profile power jack. If you want a real Lumberg jack, find those here! Takes "standard" 5.5mm plug with 2.1mm center pin. It is a tighter squeeze on the power cable than the bigger DC jacks. It'll fit, and you won't need to worry about... MSRP: Now: $0.60 Add to Cart Compare Quick view sku: DC-1002 DC Power Jack 2.1mm - Outie Stardard power jack, the external "outie" version. The body of this jack sits outside of the pedal to save space on the inside. Comes with flat washer and star washer. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 1/2" (12... MSRP: Now: $0.65 Add to Cart Compare Quick view Lumberg | sku: DC-1005 DC Power Jack 2.1mm - Lumberg 1614 09 *DISCONTINUED. Once they're gone they will not be restocked. 1614 23 is the updated Lumberg part* The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. Superior connection and fit... MSRP: Now: $1.85 Add to Cart Compare Quick view sku: DC-1001 DC Power Jack 2.1mm - PCB Mount Standard PCB mount power jack. Takes "standard" 5.5mm plug with 2.1mm center pin. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1009 9v Battery Clip - Vinyl Battery snap for 9v battery. Vinyl insulator.6" (150mm) pre-tinned leads. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1020 9v Battery Clip - Plastic Battery snap for 9v battery. 6" (150mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Now: $0.35 Add to Cart Compare Quick view sku: KIT-1000 "The Essentials" Hardware Kit The Essentials! All the standard hardware you'll need for any build. This pack includes:1x 3PDT Pro footswitch with solder lugs1x TRS enclosed 1/4" jack1x TS enclosed 1/4" jack1x DC power jack - "outie"1x 5mm LED (leave a comment in checkout if... MSRP: Now: $7.00 Add to Cart Compare Quick view Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. These are Lumberg's updated version of the discontinued 1614 09. The insertion/removal force is a bit tighter on the new model... MSRP: Now: $1.35 Add to Cart Compare SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Compare Selected × OK
Quick view Details sku: DC-1001 DC Power Jack 2.1mm - PCB Mount MSRP: Now: $0.35 Add to Cart Compare Quick view Details sku: BAT-1009 9v Battery Clip - Vinyl MSRP: Now: $0.35 Add to Cart Compare Quick view Details sku: BAT-1020 9v Battery Clip - Plastic MSRP: Now: $0.35 Add to Cart Compare Quick view Details sku: KIT-1000 "The Essentials" Hardware Kit MSRP: Now: $7.00 Add to Cart Compare Quick view Details Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 MSRP: Now: $1.35 Add to Cart Compare SALE Quick view Details sku: BAT-1022 9v Battery Clip - Plastic - Short Lead MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Details Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Quick view sku: DC-1000 DC Power Jack 2.1mm - Innie Stardard power jack, internal nut. Low profile on the outside so pedals can be wedged closer together. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 15/32" (12mm) diameter hole. Three solder lug. Switched to disconnect... MSRP: Now: $0.50 Add to Cart Compare Quick view sku: DC-1004 DC Power Jack 2.1mm - Low Profile Low profile power jack. If you want a real Lumberg jack, find those here! Takes "standard" 5.5mm plug with 2.1mm center pin. It is a tighter squeeze on the power cable than the bigger DC jacks. It'll fit, and you won't need to worry about... MSRP: Now: $0.60 Add to Cart Compare Quick view sku: DC-1002 DC Power Jack 2.1mm - Outie Stardard power jack, the external "outie" version. The body of this jack sits outside of the pedal to save space on the inside. Comes with flat washer and star washer. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 1/2" (12... MSRP: Now: $0.65 Add to Cart Compare Quick view Lumberg | sku: DC-1005 DC Power Jack 2.1mm - Lumberg 1614 09 *DISCONTINUED. Once they're gone they will not be restocked. 1614 23 is the updated Lumberg part* The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. Superior connection and fit... MSRP: Now: $1.85 Add to Cart Compare Quick view sku: DC-1001 DC Power Jack 2.1mm - PCB Mount Standard PCB mount power jack. Takes "standard" 5.5mm plug with 2.1mm center pin. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1009 9v Battery Clip - Vinyl Battery snap for 9v battery. Vinyl insulator.6" (150mm) pre-tinned leads. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1020 9v Battery Clip - Plastic Battery snap for 9v battery. 6" (150mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Now: $0.35 Add to Cart Compare Quick view sku: KIT-1000 "The Essentials" Hardware Kit The Essentials! All the standard hardware you'll need for any build. This pack includes:1x 3PDT Pro footswitch with solder lugs1x TRS enclosed 1/4" jack1x TS enclosed 1/4" jack1x DC power jack - "outie"1x 5mm LED (leave a comment in checkout if... MSRP: Now: $7.00 Add to Cart Compare Quick view Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. These are Lumberg's updated version of the discontinued 1614 09. The insertion/removal force is a bit tighter on the new model... MSRP: Now: $1.35 Add to Cart Compare SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Compare Selected × OK
Quick view Details sku: BAT-1009 9v Battery Clip - Vinyl MSRP: Now: $0.35 Add to Cart Compare Quick view Details sku: BAT-1020 9v Battery Clip - Plastic MSRP: Now: $0.35 Add to Cart Compare Quick view Details sku: KIT-1000 "The Essentials" Hardware Kit MSRP: Now: $7.00 Add to Cart Compare Quick view Details Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 MSRP: Now: $1.35 Add to Cart Compare SALE Quick view Details sku: BAT-1022 9v Battery Clip - Plastic - Short Lead MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Details Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Quick view sku: DC-1000 DC Power Jack 2.1mm - Innie Stardard power jack, internal nut. Low profile on the outside so pedals can be wedged closer together. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 15/32" (12mm) diameter hole. Three solder lug. Switched to disconnect... MSRP: Now: $0.50 Add to Cart Compare Quick view sku: DC-1004 DC Power Jack 2.1mm - Low Profile Low profile power jack. If you want a real Lumberg jack, find those here! Takes "standard" 5.5mm plug with 2.1mm center pin. It is a tighter squeeze on the power cable than the bigger DC jacks. It'll fit, and you won't need to worry about... MSRP: Now: $0.60 Add to Cart Compare Quick view sku: DC-1002 DC Power Jack 2.1mm - Outie Stardard power jack, the external "outie" version. The body of this jack sits outside of the pedal to save space on the inside. Comes with flat washer and star washer. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 1/2" (12... MSRP: Now: $0.65 Add to Cart Compare Quick view Lumberg | sku: DC-1005 DC Power Jack 2.1mm - Lumberg 1614 09 *DISCONTINUED. Once they're gone they will not be restocked. 1614 23 is the updated Lumberg part* The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. Superior connection and fit... MSRP: Now: $1.85 Add to Cart Compare Quick view sku: DC-1001 DC Power Jack 2.1mm - PCB Mount Standard PCB mount power jack. Takes "standard" 5.5mm plug with 2.1mm center pin. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1009 9v Battery Clip - Vinyl Battery snap for 9v battery. Vinyl insulator.6" (150mm) pre-tinned leads. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1020 9v Battery Clip - Plastic Battery snap for 9v battery. 6" (150mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Now: $0.35 Add to Cart Compare Quick view sku: KIT-1000 "The Essentials" Hardware Kit The Essentials! All the standard hardware you'll need for any build. This pack includes:1x 3PDT Pro footswitch with solder lugs1x TRS enclosed 1/4" jack1x TS enclosed 1/4" jack1x DC power jack - "outie"1x 5mm LED (leave a comment in checkout if... MSRP: Now: $7.00 Add to Cart Compare Quick view Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. These are Lumberg's updated version of the discontinued 1614 09. The insertion/removal force is a bit tighter on the new model... MSRP: Now: $1.35 Add to Cart Compare SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Compare Selected × OK
Quick view Details sku: BAT-1020 9v Battery Clip - Plastic MSRP: Now: $0.35 Add to Cart Compare Quick view Details sku: KIT-1000 "The Essentials" Hardware Kit MSRP: Now: $7.00 Add to Cart Compare Quick view Details Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 MSRP: Now: $1.35 Add to Cart Compare SALE Quick view Details sku: BAT-1022 9v Battery Clip - Plastic - Short Lead MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Details Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Quick view sku: DC-1000 DC Power Jack 2.1mm - Innie Stardard power jack, internal nut. Low profile on the outside so pedals can be wedged closer together. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 15/32" (12mm) diameter hole. Three solder lug. Switched to disconnect... MSRP: Now: $0.50 Add to Cart Compare Quick view sku: DC-1004 DC Power Jack 2.1mm - Low Profile Low profile power jack. If you want a real Lumberg jack, find those here! Takes "standard" 5.5mm plug with 2.1mm center pin. It is a tighter squeeze on the power cable than the bigger DC jacks. It'll fit, and you won't need to worry about... MSRP: Now: $0.60 Add to Cart Compare Quick view sku: DC-1002 DC Power Jack 2.1mm - Outie Stardard power jack, the external "outie" version. The body of this jack sits outside of the pedal to save space on the inside. Comes with flat washer and star washer. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 1/2" (12... MSRP: Now: $0.65 Add to Cart Compare Quick view Lumberg | sku: DC-1005 DC Power Jack 2.1mm - Lumberg 1614 09 *DISCONTINUED. Once they're gone they will not be restocked. 1614 23 is the updated Lumberg part* The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. Superior connection and fit... MSRP: Now: $1.85 Add to Cart Compare Quick view sku: DC-1001 DC Power Jack 2.1mm - PCB Mount Standard PCB mount power jack. Takes "standard" 5.5mm plug with 2.1mm center pin. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1009 9v Battery Clip - Vinyl Battery snap for 9v battery. Vinyl insulator.6" (150mm) pre-tinned leads. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1020 9v Battery Clip - Plastic Battery snap for 9v battery. 6" (150mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Now: $0.35 Add to Cart Compare Quick view sku: KIT-1000 "The Essentials" Hardware Kit The Essentials! All the standard hardware you'll need for any build. This pack includes:1x 3PDT Pro footswitch with solder lugs1x TRS enclosed 1/4" jack1x TS enclosed 1/4" jack1x DC power jack - "outie"1x 5mm LED (leave a comment in checkout if... MSRP: Now: $7.00 Add to Cart Compare Quick view Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. These are Lumberg's updated version of the discontinued 1614 09. The insertion/removal force is a bit tighter on the new model... MSRP: Now: $1.35 Add to Cart Compare SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Compare Selected × OK
Quick view Details sku: KIT-1000 "The Essentials" Hardware Kit MSRP: Now: $7.00 Add to Cart Compare Quick view Details Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 MSRP: Now: $1.35 Add to Cart Compare SALE Quick view Details sku: BAT-1022 9v Battery Clip - Plastic - Short Lead MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Details Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Quick view sku: DC-1000 DC Power Jack 2.1mm - Innie Stardard power jack, internal nut. Low profile on the outside so pedals can be wedged closer together. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 15/32" (12mm) diameter hole. Three solder lug. Switched to disconnect... MSRP: Now: $0.50 Add to Cart Compare Quick view sku: DC-1004 DC Power Jack 2.1mm - Low Profile Low profile power jack. If you want a real Lumberg jack, find those here! Takes "standard" 5.5mm plug with 2.1mm center pin. It is a tighter squeeze on the power cable than the bigger DC jacks. It'll fit, and you won't need to worry about... MSRP: Now: $0.60 Add to Cart Compare Quick view sku: DC-1002 DC Power Jack 2.1mm - Outie Stardard power jack, the external "outie" version. The body of this jack sits outside of the pedal to save space on the inside. Comes with flat washer and star washer. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 1/2" (12... MSRP: Now: $0.65 Add to Cart Compare Quick view Lumberg | sku: DC-1005 DC Power Jack 2.1mm - Lumberg 1614 09 *DISCONTINUED. Once they're gone they will not be restocked. 1614 23 is the updated Lumberg part* The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. Superior connection and fit... MSRP: Now: $1.85 Add to Cart Compare Quick view sku: DC-1001 DC Power Jack 2.1mm - PCB Mount Standard PCB mount power jack. Takes "standard" 5.5mm plug with 2.1mm center pin. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1009 9v Battery Clip - Vinyl Battery snap for 9v battery. Vinyl insulator.6" (150mm) pre-tinned leads. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1020 9v Battery Clip - Plastic Battery snap for 9v battery. 6" (150mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Now: $0.35 Add to Cart Compare Quick view sku: KIT-1000 "The Essentials" Hardware Kit The Essentials! All the standard hardware you'll need for any build. This pack includes:1x 3PDT Pro footswitch with solder lugs1x TRS enclosed 1/4" jack1x TS enclosed 1/4" jack1x DC power jack - "outie"1x 5mm LED (leave a comment in checkout if... MSRP: Now: $7.00 Add to Cart Compare Quick view Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. These are Lumberg's updated version of the discontinued 1614 09. The insertion/removal force is a bit tighter on the new model... MSRP: Now: $1.35 Add to Cart Compare SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Compare Selected × OK
Quick view Details Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 MSRP: Now: $1.35 Add to Cart Compare SALE Quick view Details sku: BAT-1022 9v Battery Clip - Plastic - Short Lead MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Details Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Quick view sku: DC-1000 DC Power Jack 2.1mm - Innie Stardard power jack, internal nut. Low profile on the outside so pedals can be wedged closer together. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 15/32" (12mm) diameter hole. Three solder lug. Switched to disconnect... MSRP: Now: $0.50 Add to Cart Compare Quick view sku: DC-1004 DC Power Jack 2.1mm - Low Profile Low profile power jack. If you want a real Lumberg jack, find those here! Takes "standard" 5.5mm plug with 2.1mm center pin. It is a tighter squeeze on the power cable than the bigger DC jacks. It'll fit, and you won't need to worry about... MSRP: Now: $0.60 Add to Cart Compare Quick view sku: DC-1002 DC Power Jack 2.1mm - Outie Stardard power jack, the external "outie" version. The body of this jack sits outside of the pedal to save space on the inside. Comes with flat washer and star washer. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 1/2" (12... MSRP: Now: $0.65 Add to Cart Compare Quick view Lumberg | sku: DC-1005 DC Power Jack 2.1mm - Lumberg 1614 09 *DISCONTINUED. Once they're gone they will not be restocked. 1614 23 is the updated Lumberg part* The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. Superior connection and fit... MSRP: Now: $1.85 Add to Cart Compare Quick view sku: DC-1001 DC Power Jack 2.1mm - PCB Mount Standard PCB mount power jack. Takes "standard" 5.5mm plug with 2.1mm center pin. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1009 9v Battery Clip - Vinyl Battery snap for 9v battery. Vinyl insulator.6" (150mm) pre-tinned leads. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1020 9v Battery Clip - Plastic Battery snap for 9v battery. 6" (150mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Now: $0.35 Add to Cart Compare Quick view sku: KIT-1000 "The Essentials" Hardware Kit The Essentials! All the standard hardware you'll need for any build. This pack includes:1x 3PDT Pro footswitch with solder lugs1x TRS enclosed 1/4" jack1x TS enclosed 1/4" jack1x DC power jack - "outie"1x 5mm LED (leave a comment in checkout if... MSRP: Now: $7.00 Add to Cart Compare Quick view Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. These are Lumberg's updated version of the discontinued 1614 09. The insertion/removal force is a bit tighter on the new model... MSRP: Now: $1.35 Add to Cart Compare SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Compare Selected × OK
SALE Quick view Details sku: BAT-1022 9v Battery Clip - Plastic - Short Lead MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare
SALE Quick view Details Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare
Quick view sku: DC-1000 DC Power Jack 2.1mm - Innie Stardard power jack, internal nut. Low profile on the outside so pedals can be wedged closer together. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 15/32" (12mm) diameter hole. Three solder lug. Switched to disconnect... MSRP: Now: $0.50 Add to Cart Compare Quick view sku: DC-1004 DC Power Jack 2.1mm - Low Profile Low profile power jack. If you want a real Lumberg jack, find those here! Takes "standard" 5.5mm plug with 2.1mm center pin. It is a tighter squeeze on the power cable than the bigger DC jacks. It'll fit, and you won't need to worry about... MSRP: Now: $0.60 Add to Cart Compare Quick view sku: DC-1002 DC Power Jack 2.1mm - Outie Stardard power jack, the external "outie" version. The body of this jack sits outside of the pedal to save space on the inside. Comes with flat washer and star washer. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 1/2" (12... MSRP: Now: $0.65 Add to Cart Compare Quick view Lumberg | sku: DC-1005 DC Power Jack 2.1mm - Lumberg 1614 09 *DISCONTINUED. Once they're gone they will not be restocked. 1614 23 is the updated Lumberg part* The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. Superior connection and fit... MSRP: Now: $1.85 Add to Cart Compare Quick view sku: DC-1001 DC Power Jack 2.1mm - PCB Mount Standard PCB mount power jack. Takes "standard" 5.5mm plug with 2.1mm center pin. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1009 9v Battery Clip - Vinyl Battery snap for 9v battery. Vinyl insulator.6" (150mm) pre-tinned leads. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1020 9v Battery Clip - Plastic Battery snap for 9v battery. 6" (150mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Now: $0.35 Add to Cart Compare Quick view sku: KIT-1000 "The Essentials" Hardware Kit The Essentials! All the standard hardware you'll need for any build. This pack includes:1x 3PDT Pro footswitch with solder lugs1x TRS enclosed 1/4" jack1x TS enclosed 1/4" jack1x DC power jack - "outie"1x 5mm LED (leave a comment in checkout if... MSRP: Now: $7.00 Add to Cart Compare Quick view Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. These are Lumberg's updated version of the discontinued 1614 09. The insertion/removal force is a bit tighter on the new model... MSRP: Now: $1.35 Add to Cart Compare SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Compare Selected × OK
Quick view sku: DC-1004 DC Power Jack 2.1mm - Low Profile Low profile power jack. If you want a real Lumberg jack, find those here! Takes "standard" 5.5mm plug with 2.1mm center pin. It is a tighter squeeze on the power cable than the bigger DC jacks. It'll fit, and you won't need to worry about... MSRP: Now: $0.60 Add to Cart Compare Quick view sku: DC-1002 DC Power Jack 2.1mm - Outie Stardard power jack, the external "outie" version. The body of this jack sits outside of the pedal to save space on the inside. Comes with flat washer and star washer. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 1/2" (12... MSRP: Now: $0.65 Add to Cart Compare Quick view Lumberg | sku: DC-1005 DC Power Jack 2.1mm - Lumberg 1614 09 *DISCONTINUED. Once they're gone they will not be restocked. 1614 23 is the updated Lumberg part* The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. Superior connection and fit... MSRP: Now: $1.85 Add to Cart Compare Quick view sku: DC-1001 DC Power Jack 2.1mm - PCB Mount Standard PCB mount power jack. Takes "standard" 5.5mm plug with 2.1mm center pin. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1009 9v Battery Clip - Vinyl Battery snap for 9v battery. Vinyl insulator.6" (150mm) pre-tinned leads. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1020 9v Battery Clip - Plastic Battery snap for 9v battery. 6" (150mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Now: $0.35 Add to Cart Compare Quick view sku: KIT-1000 "The Essentials" Hardware Kit The Essentials! All the standard hardware you'll need for any build. This pack includes:1x 3PDT Pro footswitch with solder lugs1x TRS enclosed 1/4" jack1x TS enclosed 1/4" jack1x DC power jack - "outie"1x 5mm LED (leave a comment in checkout if... MSRP: Now: $7.00 Add to Cart Compare Quick view Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. These are Lumberg's updated version of the discontinued 1614 09. The insertion/removal force is a bit tighter on the new model... MSRP: Now: $1.35 Add to Cart Compare SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Compare Selected × OK
Quick view sku: DC-1002 DC Power Jack 2.1mm - Outie Stardard power jack, the external "outie" version. The body of this jack sits outside of the pedal to save space on the inside. Comes with flat washer and star washer. Takes "standard" 5.5mm plug with 2.1mm center pin. Mounts in a 1/2" (12... MSRP: Now: $0.65 Add to Cart Compare Quick view Lumberg | sku: DC-1005 DC Power Jack 2.1mm - Lumberg 1614 09 *DISCONTINUED. Once they're gone they will not be restocked. 1614 23 is the updated Lumberg part* The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. Superior connection and fit... MSRP: Now: $1.85 Add to Cart Compare Quick view sku: DC-1001 DC Power Jack 2.1mm - PCB Mount Standard PCB mount power jack. Takes "standard" 5.5mm plug with 2.1mm center pin. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1009 9v Battery Clip - Vinyl Battery snap for 9v battery. Vinyl insulator.6" (150mm) pre-tinned leads. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1020 9v Battery Clip - Plastic Battery snap for 9v battery. 6" (150mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Now: $0.35 Add to Cart Compare Quick view sku: KIT-1000 "The Essentials" Hardware Kit The Essentials! All the standard hardware you'll need for any build. This pack includes:1x 3PDT Pro footswitch with solder lugs1x TRS enclosed 1/4" jack1x TS enclosed 1/4" jack1x DC power jack - "outie"1x 5mm LED (leave a comment in checkout if... MSRP: Now: $7.00 Add to Cart Compare Quick view Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. These are Lumberg's updated version of the discontinued 1614 09. The insertion/removal force is a bit tighter on the new model... MSRP: Now: $1.35 Add to Cart Compare SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Compare Selected × OK
Quick view Lumberg | sku: DC-1005 DC Power Jack 2.1mm - Lumberg 1614 09 *DISCONTINUED. Once they're gone they will not be restocked. 1614 23 is the updated Lumberg part* The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. Superior connection and fit... MSRP: Now: $1.85 Add to Cart Compare Quick view sku: DC-1001 DC Power Jack 2.1mm - PCB Mount Standard PCB mount power jack. Takes "standard" 5.5mm plug with 2.1mm center pin. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1009 9v Battery Clip - Vinyl Battery snap for 9v battery. Vinyl insulator.6" (150mm) pre-tinned leads. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1020 9v Battery Clip - Plastic Battery snap for 9v battery. 6" (150mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Now: $0.35 Add to Cart Compare Quick view sku: KIT-1000 "The Essentials" Hardware Kit The Essentials! All the standard hardware you'll need for any build. This pack includes:1x 3PDT Pro footswitch with solder lugs1x TRS enclosed 1/4" jack1x TS enclosed 1/4" jack1x DC power jack - "outie"1x 5mm LED (leave a comment in checkout if... MSRP: Now: $7.00 Add to Cart Compare Quick view Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. These are Lumberg's updated version of the discontinued 1614 09. The insertion/removal force is a bit tighter on the new model... MSRP: Now: $1.35 Add to Cart Compare SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Compare Selected × OK
Quick view sku: DC-1001 DC Power Jack 2.1mm - PCB Mount Standard PCB mount power jack. Takes "standard" 5.5mm plug with 2.1mm center pin. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1009 9v Battery Clip - Vinyl Battery snap for 9v battery. Vinyl insulator.6" (150mm) pre-tinned leads. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1020 9v Battery Clip - Plastic Battery snap for 9v battery. 6" (150mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Now: $0.35 Add to Cart Compare Quick view sku: KIT-1000 "The Essentials" Hardware Kit The Essentials! All the standard hardware you'll need for any build. This pack includes:1x 3PDT Pro footswitch with solder lugs1x TRS enclosed 1/4" jack1x TS enclosed 1/4" jack1x DC power jack - "outie"1x 5mm LED (leave a comment in checkout if... MSRP: Now: $7.00 Add to Cart Compare Quick view Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. These are Lumberg's updated version of the discontinued 1614 09. The insertion/removal force is a bit tighter on the new model... MSRP: Now: $1.35 Add to Cart Compare SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Compare Selected × OK
Quick view sku: BAT-1009 9v Battery Clip - Vinyl Battery snap for 9v battery. Vinyl insulator.6" (150mm) pre-tinned leads. MSRP: Now: $0.35 Add to Cart Compare Quick view sku: BAT-1020 9v Battery Clip - Plastic Battery snap for 9v battery. 6" (150mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Now: $0.35 Add to Cart Compare Quick view sku: KIT-1000 "The Essentials" Hardware Kit The Essentials! All the standard hardware you'll need for any build. This pack includes:1x 3PDT Pro footswitch with solder lugs1x TRS enclosed 1/4" jack1x TS enclosed 1/4" jack1x DC power jack - "outie"1x 5mm LED (leave a comment in checkout if... MSRP: Now: $7.00 Add to Cart Compare Quick view Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. These are Lumberg's updated version of the discontinued 1614 09. The insertion/removal force is a bit tighter on the new model... MSRP: Now: $1.35 Add to Cart Compare SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Compare Selected × OK
Quick view sku: BAT-1020 9v Battery Clip - Plastic Battery snap for 9v battery. 6" (150mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Now: $0.35 Add to Cart Compare Quick view sku: KIT-1000 "The Essentials" Hardware Kit The Essentials! All the standard hardware you'll need for any build. This pack includes:1x 3PDT Pro footswitch with solder lugs1x TRS enclosed 1/4" jack1x TS enclosed 1/4" jack1x DC power jack - "outie"1x 5mm LED (leave a comment in checkout if... MSRP: Now: $7.00 Add to Cart Compare Quick view Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. These are Lumberg's updated version of the discontinued 1614 09. The insertion/removal force is a bit tighter on the new model... MSRP: Now: $1.35 Add to Cart Compare SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Compare Selected × OK
Quick view sku: KIT-1000 "The Essentials" Hardware Kit The Essentials! All the standard hardware you'll need for any build. This pack includes:1x 3PDT Pro footswitch with solder lugs1x TRS enclosed 1/4" jack1x TS enclosed 1/4" jack1x DC power jack - "outie"1x 5mm LED (leave a comment in checkout if... MSRP: Now: $7.00 Add to Cart Compare Quick view Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. These are Lumberg's updated version of the discontinued 1614 09. The insertion/removal force is a bit tighter on the new model... MSRP: Now: $1.35 Add to Cart Compare SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Compare Selected
Quick view Lumberg | sku: DC-1006 DC Power Jack 2.1mm - Lumberg 1614 23 The professional standard for small, low profile panel mount DC jacks. Takes "standard" 5.5mm plug with 2.1mm center pin. These are Lumberg's updated version of the discontinued 1614 09. The insertion/removal force is a bit tighter on the new model... MSRP: Now: $1.35 Add to Cart Compare SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare Compare Selected
SALE Quick view sku: BAT-1022 9v Battery Clip - Plastic - Short Lead Battery snap for 9v battery. 3.9" (100mm) pre-tinned leads. Taller collar plastic housing. Adds additional protection from conductors shorting on something inside. With a battery installed, it takes up the same amount of space as the lower collar clips... MSRP: Was: $0.30 Now: $0.24 Add to Cart Compare
SALE Quick view Switchcraft | sku: DC-1003 DC Power Jack 2.1mm - RAPC722X CLEARANCE PRICING UNTIL GONE! Not restocking. USA Switchcraft p/n RAPC722X Standard PCB mount power jack. Optional terminal for the switch to disconnect a battery when DC is plugged in. MSRP: Was: $1.50 Now: $1.20 Add to Cart Compare
